Not Just Precision Parts, But Works of Art | Free DFM Analysis & Instant Quotes
Get Instant Quote
Company
Strength
20 Years of Experience
20 Years of Experience
72 Sets of CNC Machines
72 Sets of CNC Machines
Precision: ±0.01mm
Precision: ±0.01mm
7-15 Days Fast Shipping
7-15 Days Fast Shipping
Quality
Advantages
No Knife Marks
No Knife Marks
No Scratches
No Scratches
No Blemishes
No Blemishes
No Color Difference
No Color Difference
Technical Guides

Robot support: galvanized and passivated carbon steel parts

in the mass production of a collaborative robot load support, a joint connection base and a sensor mounting baseZinc Plating and Passivation Process for Carbon Steel PartsThis article is based on the actual production line experience, dismantling the complete technical logic from material selection to surface treatment, helping engineers and purchasers to quickly judge the feasibility and potential risks of process solutions.

Material selection and machining benchmark for carbon steel supports

Q235B or Q345B carbon steel is usually used for robot support. Q235B is suitable for static load support, its elongation is high, welding deformation is relatively controllable; Q345B is used for dynamic joint parts, yield strength is higher, and it can withstand repeated alternating stress. For CNC machining, special attention should be paid to the ferromagnetism of carbon steel, which will interfere with some magnetic tools. It is recommended to use non-magnetic pressing tools or vacuum adsorption. In terms of tolerance, it is recommended to control the key mating surface within ± 0.05mm, and the non-mating surface ± 0.1mm to meet the assembly requirements. If there is a through hole in the bracket, it is recommended to reserve a zinc allowance of 0.1 - 0.2mm before machining to avoid zinc accumulation blocking the threaded hole. The rough machined surface roughness Ra is controlled below 3.2 μ m, providing a basis for the adhesion of the subsequent zinc coating.

Galvanizing Process: Engineering Differences between Electroplating and Hot Dip Galvanizing

Robot brackets are mostly precision structural parts, and most scenes adoptZinc plating (EDC)Not hot dip zinc (HDG). Electroplating zinc layer uniform, thickness controllable (usually 5 - 15 μ m), does not change the original size of the part, suitable for brackets with tight fit clearance requirements. Hot dip zinc layer thickness (60 - 120 μ m), will produce zinc scale, easy to jam threads, damage precision fit, only suitable for large welding frames without matching requirements. Before zinc plating, it is necessary to thoroughly remove oil and rust. If the pretreatment is not clean, the zinc coating will appear pinholes and blisters, resulting in local corrosion. After zinc plating, the zinc coating and the substrate have high bonding strength, but it is susceptible to hydrogen embrittlement. Therefore, zinc plating must be carried out after zinc plating.hydrogen relief treatment, usually baked at 200 - 250 ℃ for 2 - 4 hours to release hydrogen atoms absorbed in the zinc layer. If this step is skipped, the stent may develop fine cracks after a few weeks, resulting in fracture failure.

Application Comparison of Electroplating and Hot-dip Zinc on Robot Support
characterZinc Electroplating (EDC)Hot Dip Zinc (HDG)
plating thickness5-15 μm60-120 μm
size effectAlmost no impact, suitable for precision fitThickening is obvious, easy to catch threads, only suitable for welding frames
surface appearanceBright, uniform, can be subsequently passivatedRough, zincy, usually no longer machined
corrosion resistanceGood, with passivation can reach more than 96h salt sprayExcellent, preferred for long-term outdoor environments
applicable scenariosCNC machining brackets, jointsLarge welded structure, outdoor heavy support

Passivation process: white zinc, yellow zinc and color zinc selection

Passivation is a key anti-corrosion upgrade step after zinc plating, which inhibits the electrochemical activity of zinc matrix through chemical coating.White zinc (trivalent chromium passivation)Bright white appearance, good environmental protection, hexavalent chromium free, salt spray test usually up to 72-96 hours. The current industry trend is accelerating to chromium-free passivation technology, such as silicate-phosphate composite film, its corrosion resistance is close to white zinc, and fully compliant with RoHS and REACH regulations, suitable for export robot parts.Yellow zinc (hexavalent chromium passivation)Appearance is pale yellow, salt spray performance is better, up to 120-168 hours, but due to hexavalent chromium, facing strict environmental regulations, the EU market has greatly reduced its use.Color zinc (blue zinc)The appearance is blue-purple, mainly for decoration and identification, corrosion resistance between white zinc and yellow zinc, often used for non-critical appearance parts. For robot brackets, if used in indoor or low corrosive environment, white zinc or chromium-free passivation can be used; if used in outdoor or high humidity environment, it is recommended to use high corrosion resistance chromium-free passivation or thick galvanized layer (15μm) with passivation.

Common defects and avoidance in surface treatment process

In the actual batch production, three kinds of defects are easy to appear in the zinc passivation process. The first iscoating spalling, mostly due to poor oil removal or strong pickling of the pretreatment lead to hydrogen embrittlement of the matrix, the avoidance scheme is to control the pickling time, and strictly implement the hydrogen removal process. The second isuneven passivation film, performance for local white or yellow, the reason is passivation bath concentration fluctuation or cleaning is not thorough, need to regularly titrate the bath solution and increase the number of clean water rinse. The third isZinc slag accumulation in screw holes, zinc layer after galvanizing in the hole bulge, resulting in assembly interference. Solution is to pre-coat zinc paste on the threaded hole before galvanizing, or use a special thread brush cleaning after galvanizing. For high-precision mating surface, it is recommended to communicate with the supplier "local shielding" process, that is, before galvanizing on the mating surface film, after galvanizing tear film, to ensure that the mating surface without coating accumulation.

Quality acceptance criteria and test points

Acceptance should not only look at the appearance, but also combine quantitative indicators. First,visual check, surface should be uniform, bright, no leakage plating, no scorch. Second testadhesive force, usually using the grid method (ISO 2409), requires 4B or above. The core indicators aresalt spray test(GB/T 10125 or ASTM B117), it is necessary to clearly agree on the test time and judgment standard, such as "96 hours without red rust". In addition, it is necessary to testplating thicknessGalvanizing is recommended to be measured at multiple points with a magnetic thickness gauge according to ASTM B633 to ensure that the average value is not lower than the drawing requirements. For key safety parts, spot checks are also required.hydrogen embrittlementAll test reports shall be provided with the shipment, including batch number, bath parameter record and first article inspection data for traceability.

FAQ: Common problems of galvanized passivation process for carbon steel

What special preparation is needed before galvanizing carbon steel parts?

Degreasing, acid cleaning and activation treatment are required to ensure that the surface is clean and free of oil stains to improve the adhesion of the coating. For precision mating surfaces, it is recommended to reserve coating allowance or adopt local shielding technology.

Is there a big difference in the life of chromium-free passivation and traditional hexavalent chromium passivation?

High-quality chromium-free passivation has a life close to hexavalent chromium in normal industrial environments, salt spray time is slightly shorter but can meet most robot application scenarios, and is more environmentally friendly, in line with current regulatory trends.

How to effectively solve the problem of thread hole blockage after galvanization?

Before galvanizing, apply anti-zinc paste to threaded holes, or use special thread cleaning tools after galvanizing. For high-precision threads, it is recommended to tap and galvanize first, and reserve 0.1mm fit allowance.

Can hydrogen removal be omitted?

It cannot be omitted. Especially for high-strength carbon steel or parts that have undergone deep drawing and cold deformation, hydrogen retention will lead to delayed cracking, and hydrogen removal is a key process to ensure structural safety.

How to ensure the consistency of galvanized appearance of batch products?

It is necessary to control the temperature and concentration of the bath solution, unify the loading density of parts, and ensure the uniform current density. The supplier shall have the ability to track batches and provide records of process parameters for each batch for verification.

Conclusions and next steps

Zinc plating and passivation of carbon steel parts is not a simple "adding a layer of skin", but a systematic engineering involving materials, machining, surface pretreatment, coating parameters and post-treatment. When selecting a process, priority should be given to matching the use environment, matching accuracy and regulatory requirements of the robot, rather than just looking at the unit price. If your project involves Q235/Q345 carbon steel brackets and requires corrosion resistance and appearance consistency, it is recommended to send the drawings, material grades, expected salt spray time and fit clearance requirements to the supplier for DFM review. ShowyMetal has one-stop service capability for CNC machining and surface treatment, supports customization of carbon steel parts and rapid delivery in batches. Please provide drawings for inquiry. We will provide detailed solutions based on process feasibility and cost structure.

Share:
« Previous Joint motor housing: aluminum alloy die-casting and CNC post-treatment Next » Servo driver PCB: Aluminum substrate CNC slot and heat dissipation

Related Content

Explore more articles that may interest you.

Send Your Drawing, Get a Quote in 2 Hours.

Send your STEP / DWG / PDF drawing and our engineers reply within 2 hours with a detailed quote including free DFM analysis and process recommendations — no obligation.

Send Drawing for a Quote WhatsApp Us

Send Us Your Drawing — We Handle the Rest

Send your STEP / DWG / PDF drawing and get a detailed quote with free DFM analysis and process recommendations within 2 hours. No minimum order — from 1 piece.

Live inquiries
Michael · GermanyNeed 500 aluminum brackets, please quote
Sophie · FranceLead time for CNC turned stainless shafts?
David · USANeed 1000 injection molded ABS housings
Emma · UKCan you machine 5-axis titanium parts?