Not Just Precision Parts, But Works of Art | Free DFM Analysis & Instant Quotes
Get Instant Quote
Company
Strength
20 Years of Experience
20 Years of Experience
72 Sets of CNC Machines
72 Sets of CNC Machines
Precision: ±0.01mm
Precision: ±0.01mm
7-15 Days Fast Shipping
7-15 Days Fast Shipping
Quality
Advantages
No Knife Marks
No Knife Marks
No Scratches
No Scratches
No Blemishes
No Blemishes
No Color Difference
No Color Difference
Technical Guides

Automotive parts harness connector injection molding

Under the trend of automobile electronic architecture upgrade and lightweight,Automotive parts harness connector injection moldingIt has become a core process challenge for OEMs and Tier 1 suppliers. For high-density, multi-terminal, thin-walled connector housings, traditional injection molding processes often face pain points such as warpage, shrinkage marks, abnormal insertion forces and insufficient batch consistency. This paper analyzes the engineering logic of injection molding of high-precision automobile connectors from four dimensions: material selection, mold design, process parameter optimization and inspection and acceptance, and helps procurement and R & D personnel to establish executable technical evaluation standards.

Material Selection Logic for Injection Molding of Automotive Connectors

Automotive wiring harness connectors need to withstand a wide temperature range from-40 ° C to +125 ° C, and need to meet hydrolysis resistance, oil resistance and fire protection requirements. Material selection directly determines the subsequent process window and final reliability.

  • PA66-GF30/40: Most common matrix material. Glass fiber reinforcement improves rigidity, but anisotropic warpage due to fiber orientation needs to be controlled. Usually 20% PTFE modification is added to reduce friction coefficient and reduce terminal wear.
  • PBT: Low crystallinity, size stability better than PA system, suitable for warp-sensitive precision parts. But the upper limit of temperature resistance is slightly lower than PA66, which needs to be matched according to terminal material.
  • POM: Mainly used for sliding contact surfaces, with very low friction coefficient, but insulation performance and withstand voltage rating need to be evaluated separately.

Viscosity differences between batches of materials can lead to filling imbalance. It is recommended that suppliers provide melt flow rate (MFR) stability reports and lock in the same batch production from the same batch plant.

Key points of die design for thin-wall structure and multi-terminal arrangement

Automotive connectors generally adopt thin-walled designs (wall thickness 0.8-1.2mm) to save space. Thin-walled parts have poor melt fluidity and are prone to shrinkage caused by short Shot or insufficient pressure holding.

Gate Design and Exhaust

Submarine Gate can be used to remove gate marks, but the gate length and diameter (usually 0.5-1.0mm) should be strictly controlled to prevent too fast cooling from affecting filling. At the same time, the depth of the mold exhaust groove should be controlled at 0.02-0.05mm to avoid carbon deposition affecting the appearance and ensure smooth exhaust of gas at the end of the thin wall.

Multi-terminal arrangement and cooling balance

There are multiple terminal slots inside the connector, and the cooling water circuit must achieve "balanced cooling". If the water circuit is asymmetric, the first cooling side shrinks greatly, resulting in the overall distortion of the connector. It is recommended to use Conformal Cooling, which fits the cavity contour through copper alloy inserts to ensure that the temperature difference in each terminal area is less than 5°C.

Optimization of process parameters: the key to solving warpage and shrinkage

Injection molding does not simply pursue filling the cavity, but controls the shrinkage behavior of the product through pressure transmission. For automotive connectors, the core contradiction lies in the balance between "holding time" and "cooling time".

  • injection speedThin-walled parts need high initial velocity to maintain melt temperature, it is recommended to complete 70% filling within 30% of the filling stage to reduce heat loss.
  • pressure holding strategy: Multi-stage pressure maintenance (2-3 stages) is adopted. High pressure short pressure maintenance compensates for volume contraction, and low pressure long pressure maintenance prevents ejection deformation. The cavity pressure needs to be monitored in real time through the pressure monitoring (In-Mold Sensor) to ensure that the pressure peak value of each mold is consistent.
  • mold temperature controlCrystalline materials (such as PBT) need high mold temperature (80-100°C) to increase crystallinity and reduce post-shrinkage; amorphous modified materials need lower mold temperature to lock orientation stress.

Parameters are not fixed, and dynamic fine adjustment shall be carried out in combination with specific particle dryness (moisture content of PA material shall be controlled below 0.1%). It is recommended to check process capability (Cpk) every 500 modes.

Control of surface quality and appearance consistency

Visual quality is a visual indicator of connector acceptance. Common defects include flow marks, air lines, white tops and scratches. ShowyMetal strengthens visual control during injection molding by:

  • stress relieving: For precision size parts, it is recommended to anneal at 60-70°C for 1-2 hours to release internal stress and prevent size drift during subsequent processing or assembly.
  • scratch-proof package: The finished product adopts independent blister box or pearl cotton liner to avoid friction and scratch in batch transportation. For high gloss products, the mold needs to be polished to Ra0.2μm or less, and with anti-stick release agent.
  • Online visual inspection: AOI (Automatic Optical Inspection) is deployed at the end of the injection molding machine to identify defects such as surface spots and missing materials. The data is uploaded to MES system in real time to achieve traceability.

Comparative analysis of injection molding scheme and process

Under different production scale and precision requirements, the choice of injection molding process directly affects the cost and delivery time. The following table compares the difference between conventional injection molding and precision multi-cavity injection molding for evaluation reference:

Automotive connector injection molding process comparison
dimensionality Conventional single/double cavity injection molding Precision multi-cavity (4-8 cavity) synchronous injection molding
applicable scenarios Prototype verification, small batch trial production, non-standard custom parts Mass production stage, high precision, short delivery time batch demand
mold complexity Lower, simpler waterways, lower cost High, need complex shape following waterway and balance runner, mold input high
size consistency The difference between molds is slightly large, so manual sampling is required. Small temperature difference between chambers, high consistency, Cpk>1.67
defect risk Easy to warp, obvious weld lines The defect rate is low when the control is proper, but the initial debugging period is long.
lead time Mold development 2-3 weeks Mold development 4-6 weeks, but production efficiency increased by 3-4 times

If the project is in the initial stage of verification, it is preferred to use conventional molds for rapid iteration; in the mass production stage, it is recommended to switch to multi-cavity precision molds to dilute the cost of each piece and improve the yield.

Inspection standard and acceptance process

Automotive connectors have extremely strict requirements for size and function. Acceptance depends not only on appearance, but also on functional data:

  • size detection: Key mating size (such as terminal slot width and height) shall be detected by CMM or special fixture, and the tolerance is usually controlled within ± 0.02mm. Use optical projection microscope to measure minute features.
  • behaviour of electricity: Perform contact resistance test (usually< 10mΩ)及耐压测试(1000V AC, 1min),确保绝缘可靠。
  • reliability testing: Simulate actual conditions for high temperature and high humidity storage (85 ° C/85%RH, 48 h) and vibration test to verify material interface bonding force and terminal loosening risk.

AQL 2.5 sampling inspection or full inspection shall be carried out before shipment (depending on customer requirements), and material certificate (CoM) and size report (FAI) shall be attached to ensure traceability of the whole process.

FAQ: What is the MOQ for automotive connector injection molding?

Depends on mold complexity. MOQ of single cavity mold is usually low, suitable for trial production; MOQ of 5000 pieces is recommended for multi-cavity mass production mold to balance mold amortization cost. Specific drawings should be evaluated.

FAQ: How to solve warpage deformation in thin-wall injection molding?

The core lies in balanced cooling and pressure maintenance. The shape of the water channel to ensure uniform mold temperature, combined with multi-stage pressure compensation shrinkage, and in the mold design stage to optimize the gate position and exhaust, reduce internal stress from the source.

FAQ: What level of surface finish can injection molded parts achieve?

Polishing cavity can achieve mirror effect (Ra< 0.05μm),普通精修面可达 Ra 0.2-0.4μm。若需特殊纹理,可配合蚀刻工艺,但需考虑批量一致性管控难度。

FAQ: How to ensure consistency between different batches of connectors?

By locking raw material batches, standardizing process parameters (temperature, pressure, time), implementing FAI and periodic Cpk monitoring, ShowyMetal implements 100% full size inspection and in-process inspections in batch production to ensure that lot-to-lot differences are controlled.

FAQ: How to cooperate with injection molding and CNC machining in connector manufacturing?

Injection molding is suitable for efficient mass production of main shells, while CNC machining is used for high-precision positioning holes, threaded holes or complex special-shaped structures. Hybrid processes (MIM or secondary processing after assembly) can meet high-precision requirements, and parting lines need to be clearly defined at the design stage. and cooperation surfaces.

Conclusions and recommendations for cooperation

Automotive wiring harness connector injection molding is a systematic engineering involving the deep integration of material science, mold dynamics and process control. When selecting suppliers, we should not only pay attention to the quotation, but also evaluate their DFM (Design for Manufacturing) proposal capability, process quality control system and batch delivery stability. ShowyMetal has injection molding and CNC machining capabilities, providing one-stop service from drawing optimization, mold development to batch production. If you have specific connector drawings or samples to evaluate, please send technical documents for detailed process solutions and quotations.

Share:
« Previous Dynamic Balance Correction Technology of Transmission Shaft of Automobile Parts Next » Robot Guide Slider: Steel Heat Treatment and Antirust Treatment

Related Content

Explore more articles that may interest you.

Send Your Drawing, Get a Quote in 2 Hours.

Send your STEP / DWG / PDF drawing and our engineers reply within 2 hours with a detailed quote including free DFM analysis and process recommendations — no obligation.

Send Drawing for a Quote WhatsApp Us

Send Us Your Drawing — We Handle the Rest

Send your STEP / DWG / PDF drawing and get a detailed quote with free DFM analysis and process recommendations within 2 hours. No minimum order — from 1 piece.

Live inquiries
Michael · GermanyNeed 500 aluminum brackets, please quote
Sophie · FranceLead time for CNC turned stainless shafts?
David · USANeed 1000 injection molded ABS housings
Emma · UKCan you machine 5-axis titanium parts?